Size (mm):70 mm x 150 mm x 35 mm |
This type of ball bearing is recommended when alignment of the shaft and housing is difficult and the shaft may flex. The outer ring has a spherical raceway and its center of curvature coincides with that of the bearing; therefore, the axis of the inner ring, balls and cage can deflect to some extent around the bearing center. Pressed steel cages are usually used. Since the contact angle is small, the axial load capacity is low. The permissible dynamic misalignment is approximately 0.07 to 0.12 radian (4 to 7 degrees) under normal loads.
Bearing number | 1314 |
Size (mm) | 70x150x35 |
Brand | Loyal |
Bore Diameter (mm) | 70 |
Outer Diameter (mm) | 150 |
Width (mm) | 35 |
d | 70 mm |
D | 150 mm |
B | 35 mm |
C | 35 mm |
This type is constructed with the inner ring and ball assembly contained within an outer ring which has a spherical raceway for self aligning.
Self-aligning Ball Bearings are particularly suitable for applications where misalignment occurs from errors in mounting or from shaft deflection
&&&&&&&& | ||||||||
Size (mm) | ||||||||
2314 | 70 mm x 150 mm x 51 mm | |||||||
2207-2RS | 35 mm x 72 mm x 23 mm | |||||||
2212 EKTN9 + H 312 | 55 mm x 110 mm x 28 mm | |||||||
11205G15 | 25,000 mm x 52,000 mm x 44 mm | |||||||
1213 | 65 mm x 120 mm x 23 mm | |||||||
2304 | 20 mm x 52 mm x 21 mm | |||||||
1212 | 60 mm x 110 mm x 22 mm | |||||||
2314 | 70 mm x 150 mm x 51 mm | |||||||
1208ETN9 | 40 mm x 80 mm x 18 mm | |||||||
2207 TN9 | 35 mm x 72 mm x 23 mm | |||||||
1218 | 90 mm x 160 mm x 30 mm | |||||||
S1203-2RS | 17 mm x 40 mm x 12 mm | |||||||
2210-TVH | 50 mm x 90 mm x 23 mm | |||||||
2200-2RS | 10 mm x 30 mm x 14 mm | |||||||
1306-K+H306 | 30 mm x 72 mm x 19 mm | |||||||
1320 | 100 mm x 215 mm x 47 mm | |||||||
126 | 6 mm x 19 mm x 6 mm | |||||||
1315K | 75 mm x 160 mm x 37 mm | |||||||
1218 | 90 mm x 160 mm x 30 mm | |||||||
2200G14 | 10,000 mm x 30,000 mm x 14,000 mm | |||||||
2313SK | 65 mm x 140 mm x 48 mm | |||||||
11308G15 | 40,000 mm x 90,000 mm x 58 mm | |||||||
1214 | 70 mm x 125 mm x 24 mm | |||||||
2320S | 100 mm x 215 mm x 73 mm | |||||||
1206-K-TVH-C3 + H206 | 30 mm x 62 mm x 16 mm | |||||||
2211-2RSTN9 | 55 mm x 100 mm x 25 mm | |||||||
2303-2RSTN9 | 17 mm x 47 mm x 19 mm | |||||||
1320K | 100 mm x 215 mm x 47 mm | |||||||
TSM 08-01 BB-E | - | |||||||
2206-2RS | 30 mm x 62 mm x 20 mm | |||||||
2214E-2RS1TN9 | 70 mm x 125 mm x 31 mm | |||||||
1205 | 25 mm x 52 mm x 15 mm | |||||||
2315 | 75 mm x 160 mm x 55 mm | |||||||
1219 | 95,000 mm x 170,000 mm x 32,000 mm | |||||||
2311 | 55 mm x 120 mm x 43 mm | |||||||
2217S | 85 mm x 150 mm x 36 mm | |||||||
2303-2RS | 17 mm x 47 mm x 19 mm | |||||||
2305-TVH | 25 mm x 62 mm x 24 mm | |||||||
2219 | - | |||||||
1314 | 70 mm x 150 mm x 35 mm |
Copyright © 2017 - 2024BOYAL INDUSTRIES GMBH All Rights Reserved